Kitchen guide

HDHMR or plywood for a modular kitchen in Delhi

Bajrang Bali Plywood, Vishnu Garden, DelhiUpdated October 20264 min read

Short answer

Both boards work in a modular kitchen. HDHMR, at 850+ kg/m³ density, gives a smooth, uniform surface and strong screw hold, which suits laminated units. BWP plywood is the safer pick where water stays, such as under the sink. A mix of the two is a safe plan.

Plywood: layersHDHMR: one dense core
Plywood is built from layers. HDHMR is pressed from fibre into one dense, even core.

What is the difference between HDHMR and plywood?

Plywood is made of thin wood layers glued with the grain crossing. HDHMR (High Density High Moisture Resistant) is made of pressed wood fibre bonded with resin, so it is the same all the way through. Its density is above 850 kg/m³.

That one difference explains most of what follows: how the surface takes laminate, how screws grip, and how each board reacts to water.

Plywood has been the default for Indian kitchens for decades, and good BWP plywood is still hard to beat in wet spots. HDHMR is the newer option that many modular kitchen makers now prefer for its flat, even face. Ask your carpenter which one he has fabricated before, because a familiar board is cut and fitted more cleanly.

HDHMR vs plywood: which is better for a kitchen?

Neither wins everywhere. Here is how they compare on the points that matter in a kitchen.

PointHDHMRPlywood
StructureOne dense core, no layersLayers of wood veneer
Surface for laminateVery smooth, no grain to show throughGood, quality depends on the sheet
Screw holdStrong, even grip for hinges and drawer slidesGood, depends on ply quality
Near waterMoisture stable, but seal cut edgesBWP is the strongest choice for wet spots
WeightHeavierLighter
Best useCarcass, shutters, drawersSink base and other wet zones

Weight comparison is general industry knowledge. Density and screw hold follow our HDHMR page.

Which board should I use for each part of the kitchen?

  • Carcass (the boxes): 12 mm or 18 mm HDHMR, or BWR plywood for dry zones.
  • Shutters: 16.75 mm both-side laminated HDHMR is the usual choice for a standard shutter.
  • Sink base: BWP plywood, or HDHMR with every cut edge sealed.
  • Drawer bottoms: 8 mm HDHMR or 6 mm plywood.
  • Bathroom vanity: 18 mm sealed HDHMR with a BWP back panel.

Read the grade guide for plywood in MR vs BWR vs BWP plywood.

Which HDHMR variant should I buy?

The same dense core comes in four finishes:

  1. Plain: raw board, ready for your own laminate, paint or veneer.
  2. Single side: one face laminated. Use it for carcass and drawers, with the plain face inside.
  3. Both sides: two laminated faces, for shutters where both sides are seen.
  4. Fabric: textile finish for headboards and accent panels.

How do I decide between them in three steps?

  1. Mark the wet spots: sink, dishwasher, water purifier. Use BWP plywood or sealed HDHMR there.
  2. Choose your finish. For laminate, paint or acrylic, HDHMR gives a flat base. See laminates and veneers.
  3. Ask your carpenter which board he is comfortable fabricating, then check a sample at the store.

You can also try shutter colours in the kitchen visualizer before you order.

Can I use HDHMR for wardrobes and shelves too?

Yes. HDHMR holds screws well, which matters when you hang full-extension drawer slides, and its flat surface keeps laminate edges crisp. For shelves that span 800 mm or more, use 18 mm so they do not sag under weight.

What mistakes should I avoid with kitchen boards?

  • Leaving cut edges bare near the sink. Both boards are weakest at raw edges, so seal or edge-band them.
  • Going too thin. Use 18 mm for heavy units and long shelves, and keep 6 to 8 mm for drawer bottoms only.
  • Ignoring weight. HDHMR is heavier, so wall-hung units need proper fixings and a sound wall.
  • Judging by price alone. A cheaper board that swells in two monsoons costs more in the end.

Common questions

Is HDHMR better than plywood for a kitchen?

Not always better, but often a good fit. HDHMR is dense, smooth and holds screws well, so it suits laminated kitchen units. Plywood in BWP grade is still the safer pick for the sink area where water stays.

Does HDHMR swell in water?

HDHMR is made to resist moisture and has no layers to split, but standing water on raw cut edges can still damage it. Keep edges sealed or edge-banded and fix leaks quickly.

Can HDHMR be used for a bathroom vanity?

Yes, with care. Use 18 mm HDHMR, seal every cut edge, and pair it with a BWP back panel so the vanity stays protected against the wall.

Updated October 2026.

Related products and tools

More guides

Call Now WhatsApp