Which board for CNC jaali: MDF, HDHMR, WPC or plywood
Short answer
For indoor painted jaali, MDF or HDHMR gives the cleanest CNC cuts. Use WPC for balconies, bathrooms and any damp spot, since it is waterproof and termite-proof. Plywood suits larger, simple patterns but can chip on fine detail. Panels are usually 12 to 18 mm thick.
- What is a CNC jaali and where is it used?
- MDF, HDHMR, WPC or plywood: which is best for jaali?
- Which board should I pick for each spot?
- What thickness should a jaali panel be?
- How do I get a clean jaali finish?
- What mistakes break a CNC jaali?
- Jaali or louvers: which should I choose?
What is a CNC jaali and where is it used?
A jaali is a decorative screen with a repeating cut-out pattern. A CNC router cuts the pattern from a design file, so even fine, repeating shapes come out the same every time.
In homes it is used for room dividers, pooja units, TV and wall panels, and balcony screens. Browse patterns on our CNC designs page.
Traditional jaali was carved in stone or wood by hand. A CNC jaali brings that look into a flat, light board, so it is practical for flats where weight and wall strength matter. The pattern is what you notice, but the board you choose decides how long it lasts.
MDF, HDHMR, WPC or plywood: which is best for jaali?
The board decides how clean the cut is, how it takes paint and whether it survives damp.
| Board | Cut quality | Damp or outdoor | Best for |
|---|---|---|---|
| MDF | Very clean, even on fine detail | Indoors only | Painted pooja units and wall panels |
| HDHMR | Clean, strong edges | Moisture resistant, seal the edges | Partitions and laminated panels |
| WPC | Clean, cuts like wood | Waterproof and termite-proof | Balconies, bathrooms, outdoor screens |
| Plywood | Layers show on edges, may chip on fine cuts | BWP for damp spots | Larger, simple patterns with a wood look |
MDF, WPC and HDHMR facts follow our WPC, block board and MDF page and HDHMR page. Cut quality comparisons are general guidance.
Which board should I pick for each spot?
- Living room divider: 18 mm MDF or HDHMR, painted or laminated.
- Pooja unit: MDF, painted. Its smooth face takes paint flat.
- Backlit wall panel: 12 mm MDF.
- Balcony or window screen: WPC, since it does not swell or rot.
- Wood-look screen: plywood with a simple pattern and a polish or veneer.
What thickness should a jaali panel be?
Use 12 mm for wall-mounted panels and backlit screens. Use 18 mm for partitions, doors and anything freestanding, since it flexes less.
As a rule of thumb, keep the narrowest bridge between two cut-outs at least as wide as the board is thick. Thin bridges snap during cutting or handling. Ask your designer to check the file before it goes to the machine.
How do I get a clean jaali finish?
- Cut first, then sand lightly to remove fuzz from the routed edges.
- Prime the face and the inside of every cut-out, not just the front.
- Paint or laminate all sides so moisture cannot enter from the back.
- Mount on a frame or a backing board, and add LED strips behind if you want a glow.
For wall cladding in other styles, see decorative panels and louvers.
What mistakes break a CNC jaali?
- Thin bridges. The narrow strips between cut-outs snap when the panel is lifted or screwed.
- Using MDF outdoors. It swells at the cut edges once it gets wet.
- Painting only the front. Moisture enters through the back and the inside of the pattern.
- Wrong pattern size. A tiny pattern vanishes from across the room, and a huge one looks heavy. Judge the scale against the wall before you order.
Jaali or louvers: which should I choose?
A jaali is custom: you choose the pattern and it is cut to your wall size. Louvers come ready in set lengths, and WPC and PVC louvers install in a single afternoon. If you want a quick, clean look, compare louver families. If you want a pattern that is yours alone, go for a CNC jaali.
Common questions
Which is the best material for CNC jaali?
For indoor jaali, MDF and HDHMR give the cleanest cuts and a smooth base for paint. For balconies and damp spots, choose WPC. Pick plywood only for simple, larger patterns.
Can I use MDF jaali in a balcony?
Not outside. MDF absorbs moisture and swells once water reaches it. For balconies and open areas use WPC, which is waterproof and termite-proof.
What thickness should a jaali panel be?
12 mm suits wall-mounted panels and backlit screens. 18 mm is better for partitions and doors, because it flexes less. Finer patterns need wider bridges between the cut-outs.
Updated October 2026.

